Home > Electronics
Choose a sub category:
Batteries Electronic Boost Controller Engine Management Systems
Gauges Sensors / Wiring Turbo Timers
Sort By:
Page of 1
AEM Inlet Air Temperature Sensor Kit ( AIT ) with 3/8th Alum Bung and Connector Omni Power 3 Bar MAP Sensor Evo 8/9/10 Omni Power 4 Bar MAP Sensor Evo 8/9/10
Intake Air Temp Sensor For more than stock amount of boost For more than stock amount of boost
AEM Bosch LSU 4.9 UEGO Replacement Sensor GrimmSpeed Electronic Boost Control Solenoid 3 Port Evo 8/9 ETS Battery Tray Evo 8/9
ETS Battery Tray Evo 8/9
Our Price: $145.00
Replacement sensor for the new AEM UEGO Wideband AFR (30-4110)
GrimmSpeed Electronic Boost Control Solenoid 3 Port Evo 8/9

The GrimmSpeed Electronic Boost Control Solenoid is designed to work with your factory computer (requires tuning). It will not reduce the life of your factory computer because it is designed to draw the same ammount of power as the factory BCS but flows better and reacts faster. It plugs in and requires no splicing or soldering of resistors. With the included bracket you can bolt it in, plug in the connector, and start tuning for fast boost response, increased boost pressure and free up lots of power. Planning on returning the car to stock? Just reverse installation.

*Why run an Electronic BCS over a Manual Boost Controller?*
A MBC allows you to run higher than stock boost levels by preventing the wastegate from opening at its rated pressure. It does a great job at this but if boost is available under the MBC setting it will give you that full boost. So for instance, you set your MBC to 18psi because from 3000-6000rpm thats what you want. But then say you get detonation with 18psi when you are at 7000rpm unless you are below 16psi. With a MBC, you do not have this control so you are forced to run 16psi through the entire rev range. With an electronic boost controller you could run 18psi from 3000-6000 and 16psi at 7000rpm because you can tune the boost map in the ECU which will allow you to run the maximum amount of boost at every given rpm. This gives you more power throughout the range and better control. Revolutionizing the boost solenoid market, we have created model specific install brackets that allow you to directly fit our Boost Solenoid into your vehicle for a factory fit. No more Zip-tying! We give you the factory fitment you have been waiting for.

Staying with the OEM fitment theme, the GrimmSpeed Electronic Boost Control Solenoid uses an OEM style wiring harness so you can simply unplug your OEM solenoid and plug ours in. No more cutting the oem wiring and crimping wires together!

Also new to the electronic boost solenoid market, we have used ultra low-profile hose fittings to keep the unit as small and clean as possible. The hose fittings are nickel plated brass so you don't have to worry about them snapping off like the plastic hose fittings!

*More Features*
* Users can use AN fittings with the solenoid.
* MAC Valve has completely custom made the valve for us(only MAC valve on the market to be custom made for automotive tuning use).
* Specifically designed by GrimmSpeed™ to work safely with the factory ECU (requires tuning) and to reliably handle the vibrations and temperatures of your engine bay!
* Direct bolt in mounting bracket and hardware included!
* Faster response and greater flow than any other valve out there. (by more than 10%!)
* Nickel plated brass fittings. (unlike the competitors failure prone plastic fittings)
For small battery
AEM 3.5 BAR MAP or 50 PSIA Stainless Steel Sensor Kit AEM 5 BAR MAP or 75 PSIA Stainless Steel Sensor Kit Odyssey Dry Cell Battery - Non Spillable (Includes SAE Terminal Kit)
3.5 Bar Stainless Sensor 5 Bar Stainless Sensor Includes SAE Terminal Kit
Innovate MTX-L: Digital Wideband Air/Fuel Ratio Gauge TurboSmart e-Boost Street 40 PSI TurboSmart e-Boost2 Black 60mm 60 PSI
Insurance For Your Motor. Maximum Boost Level: 40PSI / 2.72BAR Standard 60mm Gauge Housing
Maximum Boost Level: 60PSI / 2.72BAR
TurboSmart e-Boost2 Black Silver 60mm 60 PSI TurboSmart e-Boost2 White Silver 60mm 60 PSI TurboSmart e-Boost2 White Black 60mm 60 PSI
Standard 60mm Gauge Housing
Maximum Boost Level: 60PSI / 2.72BAR
Standard 60mm Gauge Housing
Maximum Boost Level: 60PSI / 2.72BAR
Standard 60mm Gauge Housing
Maximum Boost Level: 60PSI / 2.72BAR